|
CN
Battery Backup Power Supply

Model: FS-DC121820B

Battery Backup Power Supply


  • Full AC input range: 100~240V.
  • Withstand 300VAC surge input for 5 seconds.
  • Protection: short circuit / overload / over voltage / over temperature.
  • Forced air cooling by built in DC fan when the current exceeds 12A.
  • Built-in cooling fan controlled by thermal-switch.
  • Withstand 5G vibration test.
  • High operating temperature is up to 70℃.
  • Operating altitude is up to 5000 meters (note 8).
  • High efficiency, long service life, high reliability.
  • LED indicators show working condition of each channel and total output power on.
  • Multiple DC outputs, and each channel has over current (PTC/Tube fuse) and surge protection.
  • With battery charger to connect backup battery and space to hold it inside(1pc 7Ah ~20Ah battery).
advantages


1Input: AC100-240V, 50-60Hz

2 Voltage ADJ. : DC13-15V

3 Thicker cooling fin by free air

4 PCB plate, better heat releasing

5Battery charging: lead acid battery, no delay

6High quality transformer with 100% copper wire

7 PFC (Power Factor Correction), improve power efficiency

8 Patent External Indicators: easy to check power working condition

9Backup battery interfaces, provide power continuously in case of power failure

10Multiple-Channel independent tube fuse or PTC fuse, can fuse automatically while short circuit, over current or over load


NOTES

1 . All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.

2 . Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3 . Tolerance: includes set up tolerance, line regulation and load regulation.

4 .  Line regulation is measured from low line to high line at rated load.

5 . Load regulation is measured from 0% to 100% rated load.

6 Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quickly may lead to increase of the set up time.

7 . Integrated power supply system, when there is one channel over current, the PTC goes shortcut or glass fuse blow, this does not affect other channels. when over current fault is removed, PTC resumes automatically or replace broken glass fuse by hand, and this channel recovered to normal working state. When the peak load of the unit reaches 150% and delivers for over 1 second, it enters hiccup mode and recovers once rated current lower than 150%.

8 . The ambient temperature derating of 5℃/1000m is needed for operating altitude greater than 2000m(6500G).

9 . Adjusted the output voltage to the maximum voltage after the battery is saturated since the battery backup takes the output voltage to charge.


Technical Specifications

MODEL

FS-DC121820B

OUTPUT

DC VOLTAGE

13.8V

RATED CURRENT

20A

CURRENT RANGE

0-20A

RATED POWER

276W

VOLTAGE ADJ.RANGE

11.5V-14.5V

OUTPUT CHANNELS

18-CH

EACH OUTPUT CURRENT

1.1A

FUSE

PTC Fuse, DC30V2A

VOLTAGE TOLERANCE (Note3)

±1.5%

LINE REGULATION (Note4)

±0.5%

LOAD REGULATION (Note5)

±0.5%

RIPPLE&NOISE (Note2)

150mVp-p

SETUP, RISE TIME

1500ms, 50ms/230VAC  1500ms, 50ms/115VAC(at full load)

HOLD UP TIME (Typ.)

15ms/230VAC 12ms/115VAC(at full load)

INPUT

VOLTAGE RANGE

96-264V

AC CURRENT (Typ.)

2.9A/115VAC

1.4A/230VAC

FREQUENCY RANGE

47-63Hz

EFFICIENCY (Typ.)

85%

LEAKAGE CURRENT

<2mA/ 240VAC

INRUSH CURRENT (Typ.)

60A/230VAC

60A/115VAC

PROTECTION

OVERLOAD(Note.7)

When the current exceeds the fuse rating (ambient 25 ℃), the fuse disconnects

110 ~ 140% rated output power

Protection type: Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

18-21V

Hiccup mode, recovers automatically after fault condition is removed.

OVER TEMPERATURE

Hiccup mode, recovers automatically after fault condition is removed

FUNCTION

FAN ON/OFF CONTROL(Typ.)

Hr1≥65 FAN ON, ≤55 FAN OFF

ENVIRONMENT

WORKING TEMP.

-25-70(Refer to "Derating Curve")

WORKING HUMIDITY

20%---90% RH non-condensing

STORAGE TEMP, HUMIDITY

-40-----85 10%---95% RH

TEMP. COEFFICIENT

± 0.03%/ 50 (0 ~ 50)

VIBRATION

10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes

SAFETY

SAFETY STANDARDS

IEC/EN/UL/CSA 60950 GB4943

WITHSTAND VOLTAGE

I/P-O/P:3KVAC, I/P-FG:2KVAC, O/P-FG0.5KVAC

EMC EMISSION

Compliance to BSMI CNS13438, EAC TP TC 020

EMC IMMUNITY

Compliance to EAC TPTC 020

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC / 25 / 70% RH

OTHERS

MTBF

≥327.9K hrs min. MIL-HDBK-217F25)

DIMENSION (L*W*H mm)

324.5*251.5*80.5mm  (L*W*H)

PACKING

5pcs /13.1kg / 0.06m³/ CTN

PRODUCT WEIGHT

2.42KGS


Applications

• Analog Camera & DVR

• Landscape light strip

• Access control lock and alarm system